After numerous studies of different people's weights and heights, these steps offer the perfect solution for getting into your vehicle without the sacrifice of changing the way your vehicles exterior looks. Powered by two independent motors, the Amp Steps get their signal from the door looking mechanism and works in a split second to produce a step that's fast and study. The Automatic Deployable Amp Research Boards are engaged once you open the any door of your truck or SUV. Made in USA, the AMP Research PowerStep is backed by a 5 Year, 60,000 mile warranty. 14 inches.Įach kit includes a AMP Research LED light kit, two running boards assemblies with wire harness, electronic controller, mounting hardware and detailed installation guide. The distance from the interior floor board to the top of the deployed step is approx. The Amp Research PowerStep is covered by a limited 5 Year warranty. The Amp Research PowerStep Installation Guide. If you have any questions call us at 323.276.2999. Our experience in Sales and Distribution gives us the edge that no one else can provide. We stock the largest inventory in the nation. Locate the front door-ajar signal wire (light green with black stripe) on large connector located behind the connector of step 2.ElectricStep, AMP Research Official Authorized In Stock Shipping Center. There should be two wires of this color use the wire located on the row closest to the plug release.ĥ. Locate the rear door-ajar signal wire (dark blue with white stripe) wire on black connector below the hood-release lever (Area-A in Figure A-1). There should be two wires of this color use the wire located on the row closest to the plug release.Ģ. Locate the rear door-ajar signal wire (orange) on black connector below the hood-release lever (Area-A in Figure A-1). Wrap all connections with electrical tape and secure any loose wires.Ģ. Make certain that the leg with the diode is towards the top.ĥ. Cut each wire and install the Single Diode Harnesses as oriented in Figure B-2. Open wire wrap of the bundles and locate the front and rear doorajar signal wires (dark blue with white stripe), one found in each bundle.Ĥ. Locate the two wire bundles running up along kick panel area underneith glove compartment as shown in the above figures.ģ. After timming to correct length, connect the grey with black stripe trigger wire from step one to the blue connector of Single Diode Harness installed in previous step.Ĩ. Cut this wire and install Single Diode Harness as oriented in Figure A-3.ħ. Locate the front door-ajar signal wire (tan) on large connector located behind the connector of step 2.Ħ. After timming to correct length, connect the light blue with black stripe trigger wire from step one to the blue connector of Single Diode Harness installed in previous step.ĥ. Cut this wire and install Single Diode Harness as oriented in Figure A-2.Ĥ. There should be two wires of this color use the wire located on the row closest to the plug release.ģ. After removing the front door step plate and kick plate, lift carpet and pull Powerstep trigger wires through floor of truck.Ģ. Locate the rear door-ajar signal wire (dark blue with white stripe) on black connector below the hood-release lever (Area-A in Figure A -1). The Power-Step will not work with a incorrectly installed diode harness.ġ. Loose wires can be damaged and may cause a failure in the Powerstep's function.ĪTTENTION: Pay close attention to the orientation of the diode harnesses. Make sure to secure all wires after install. Under these circumstances you will need to locate the door-ajar signal wires.ģ. Occassionally the wire colors do not match the wire schematics. Do not tap into anything with a thicker gage than this.Ģ. All of the signal wires tapped into will be 18Ga. Attach routed wire from Powerstep harness to Posi-Tap connector.ġ. The longer of the two wires from step-1 will be routed to the door panel through front door accordian. door-ajar signal wire (black with a white stripe).Ħ. Apply Posi-Tap connector to the above found wire.ħ. After removing the door panel, you will access the wire bundle at the black cam-plug from window control panel (Area -C). Strip wire back approx 3/8” and attach to Posi-Tap connector.ĥ. Apply Posi-Tap connector to the above found wire.Ĥ. rear door-ajar signal wire (green with a black stripe).ģ. Open wire bundle located under front door step plate and locate the 18Ga. After removing the front door step plate, lift carpet and pull Powerstep trigger wires through floor of truck.Ģ.
0 Comments
Leave a Reply. |